TOPOLOGI
R1(config)#int s0/0
R1(config-if)#ipv6 address 123::1/100
R1(config-if)#ipv6 address fe80::1 link-local
R1(config-if)#encapsulation frame-relay
R1(config-if)#frame-relay map ipv6 123::2 102 broadcast
R1(config-if)#frame-relay map ipv6 fe80::2 102
R1(config-if)#frame-relay map ipv6 123::3 103 broadcast
R1(config-if)#frame-relay map ipv6 fe80::3 103
R1(config-if)#ipv6 rip 1 enable
R1(config-if)#int lo0
R1(config-if)#ipv6 address 1::1/128
R1(config-if)#ipv6 rip 1 enable
R2(config)#ipv6 unicast-routing
R2(config)#int s0/0
R2(config-if)#ipv6 address 123::2/100
R2(config-if)#ipv6 address fe80::2 link-local
R2(config-if)#encapsulation frame-relay
R2(config-if)#frame-relay map ipv6 123::1 201 broadcast
R2(config-if)#frame-relay map ipv6 fe80::1 201
R2(config-if)#frame-relay map ipv6 123::3 203 broadcast
R2(config-if)#frame-relay map ipv6 fe80::3 203
R2(config-if)#ipv6 rip 1 enable
R2(config-if)#int lo0
R2(config-if)#ipv6 address 2::2/128
R2(config-if)#ipv6 rip 1 enable
R3(config)#ipv6 unicast-routingKonfig pada router yang menjadi frame relay Switch
R3(config)#int s0/0
R3(config-if)#ipv6 address 123::3/100
R3(config-if)#ipv6 address fe80::3 link-local
R3(config-if)#encapsulation frame-relay
R3(config-if)#frame-relay map ipv6 123::1 301 broadcast
R3(config-if)#frame-relay map ipv6 fe80::1 301
R3(config-if)#frame-relay map ipv6 123::2 302 broadcast
R3(config-if)#frame-relay map ipv6 fe80::2 302
R3(config-if)#ipv6 rip 1 enable
R3(config-if)#int lo0
R3(config-if)#ipv6 address 3::3/128
R3(config-if)#ipv6 rip 1 enable
FRSW(config-if)#ipv6 unicast-routing
FRSW(config)#int s0/0
FRSW(config-if)#encapsulation frame-relay
FRSW(config-if)#frame-relay intf-type dce
FRSW(config-if)#frame-relay lmi-type cisco
FRSW(config-if)#frame-relay route 102 int s0/1 201
FRSW(config-if)#frame-relay route 103 int s0/2 301
FRSW(config-if)#ipv6 rip 1 enable
FRSW(config-if)#int s0/1
FRSW(config-if)#encapsulation frame-relay
FRSW(config-if)#frame-relay intf-type dce
FRSW(config-if)#frame-relay lmi-type cisco
FRSW(config-if)#frame-relay route 201 int s0/0 102
FRSW(config-if)#frame-relay route 203 int s0/2 302
FRSW(config-if)#ipv6 rip 1 enable
FRSW(config-if)#int s0/2
FRSW(config-if)#encapsulation frame-relay
FRSW(config-if)#frame-relay intf-type dce
FRSW(config-if)#frame-relay lmi-type cisco
FRSW(config-if)#frame-relay route 301 int s0/0 103
FRSW(config-if)#frame-relay route 302 int s0/1 203
FRSW(config-if)#ipv6 rip 1 enable
Tes dengan ping
R1#ping 1::1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1::1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 0/0/4 ms
R1#ping 2::2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 2::2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 4/27/76 ms
R1#ping 3::3
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 3::3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 8/21/44 ms